8/1/2023 0 Comments Ntopng vmware appliance![]() ![]() Fortunately, the market now offers many good software solutions, both commercial and open source, for network monitoring. Get storage statistics for each logical disk.Ĭom.Ĭom.Ĭom.Ĭom.Ĭom.If you don’t know the state of your network, you’re like a blind pilot, inevitably headed for disaster. Get network statistics for all interfaces that are up and running.Ĭom.Ĭom.Ĭom.Ĭom. Get load averages (over 1, 5, and 15-minute intervals).Ĭom.Ĭom.Ĭom.Ĭom. Otherwise, this command just replaces the servers in NTP configuration with the NTP servers that you provide as input.Ĭom.Ĭom.Ĭom. If the time synchronization is set by using NTP, the NTP daemon is restarted to reload the new NTP configuration. This command deletes old NTP servers from the configuration and sets the input NTP servers in the configuration. Otherwise, this command just deletes servers from the NTP configuration.Ĭom.t If the time synchronization mode is NTP-based, the NTP daemon is restarted to reload the new NTP configuration. This command deletes NTP servers from the configuration. Otherwise, this command just adds servers to the NTP configuration.Ĭom.leteĭelete NTP servers. If the time synchronization is NTP-based, then NTP daemon is restarted to reload the new NTP servers. This command adds NTP servers to the configuration. If time synchronization method is not set by using NTP, the NTP status is displayed as down.Ĭom.server.addĪdd NTP servers. The ntp.get command always returns the NTP server information, even when the time synchronization method is not set to NTP. If you run the tymesync.get command, you can retrieve the current time synchronization method (by using NTP or VMware Tools). A destination/prefix of the type 0.0.0.0/0 (for IPv4) or ::/0 (for IPv6) refers to the default gateway. A destination/prefix of the type 0.0.0.0/0 (for IPv4) or ::/0 (for IPv6) refers to the default gateway.Ĭom.leteĬom.routes.list Set IPv6 network configuration for an interface.Ĭom.routes.addĪdd static routing rules. Get IPv6 network configuration for all configured interfaces.Ĭom.t Get IPv6 network configuration for interfaces.Ĭom.ipv6.list Set IPv4 network configuration for an interface.Ĭom.ipv6.get If the interface is configured to use DHCP for IP address assignment, the lease of the interface is renewed.Ĭom.t Renew IPv4 network configuration on interfaces. Get IPv4 network configuration for all configured interfaces.Ĭom.ipv4.renew Get IPv4 network configuration for interfaces.Ĭom.ipv4.list Get a list of available network interfaces, including interfaces that are not yet configured.Ĭom.ipv4.get Get information about a particular network interface.Ĭom.interfaces.list Get an ordered list of inbound IP addresses that are allowed or denied by a firewall rule.Ĭom.interfaces.get If the host is configured to acquire DNS servers and host name by using DHCP, a DHCP refresh is forced.Ĭom.Īdd a firewall rule to allow or deny access from an incoming IP address.Ĭom.ĭelete a specific rule at a given position or delete all rules.Ĭom. This method fails if you use DHCP.Ĭom.Ĭom. Generate diagnostics report for SNMP agent.Ĭom.Ĭom.Ĭom.Ĭom.Ĭom.Ĭom.Īdd a DNS server. Generate localized keys for secure SNMPv3 communications.Ĭom.snmp.limitsĬom.snmp.resetĬom.tĬom.snmp.stats Update local user account properties, such as role, full name, enabled status, and password.Ĭom.snmp.disableĬom.snmp.enableĬom.snmp.getĬom.snmp.hash Update the password of a logged in user or of the user that you specify in the username parameter.Ĭom.t Set enabled state of the SSH-based controlled CLI.Ĭom.user.addĬom.leteĬom.user.getĬom.user.listĬom. Get enabled state of the SSH-based controlled CLI.Ĭom.ssh.set Set enabled state of Bash shell, that is, access to Bash shell from within the controlled CLI.Ĭom.ssh.get Get information about the state of Bash shell, that is, access to Bash shell from within the controlled CLI.Ĭom.t Set enabled state of the Direct Console User Interface (DCUI TTY2).Ĭom.shell.get Get information about the state of the Direct Console User Interface (DCUI TTY2).Ĭom.t ![]() Set enabled state of console-based controlled CLI (TTY1).Ĭom.dcui.get Get information about the state of the console-based controlled CLI (TTY1).Ĭom.t Validate restore parameters of a restore job without starting the job.Ĭom.consolecli.get Validate parameters for a backup job without starting the job.Ĭom.job.cancelĬom.job.createĬom.job.getĬom.validate Get a list of the vCenter Server components that can be included in a backup job.Ĭom.parts.getĬom.validate Query a range of values for the monitored items.Ĭom.job.cancelĬom.job.createĬom.job.getĬom.job.listĬom.parts.list Get the time of the last check of the health status. ![]() API Commands Available in vCenter Server API CommandĬom.getĬom.getĬom.lastcheck ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |